I do not know if it is really a problem, but it seems that the IC-7410’s USB I/F does not work in my new environment if I use the ports, either USB 2.0 or USB 3.0, on the motherboard.
% dmesg [ 20.737793] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 31.693171] usb 1-4: new full-speed USB device number 4 using xhci_hcd [ 31.805430] usb 1-4: Device not responding to setup address. [ 32.026386] usb 1-4: New USB device found, idVendor=0451, idProduct=2046 [ 32.026388] usb 1-4: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 32.026540] usb 1-4: ep 0x81 - rounding interval to 1024 microframes, ep desc says 2040 microframes [ 32.027075] hub 1-4:1.0: USB hub found [ 32.027331] hub 1-4:1.0: config failed, can't read hub descriptor (err -22)
The message differs on different ports, or maybe on different occasions.
[ 20.733797] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 30.860159] usb 1-5: new full-speed USB device number 4 using xhci_hcd [ 30.972376] usb 1-5: Device not responding to setup address. [ 31.176527] usb 1-5: Device not responding to setup address. [ 31.380573] usb 1-5: device not accepting address 4, error -71 [ 31.492670] usb 1-5: new full-speed USB device number 5 using xhci_hcd [ 31.621108] usb 1-5: device descriptor read/all, error -71 [ 31.732861] usb 1-5: new full-speed USB device number 6 using xhci_hcd [ 31.749699] usb 1-5: New USB device found, idVendor=0451, idProduct=2046 [ 31.749701] usb 1-5: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 31.749845] usb 1-5: ep 0x81 - rounding interval to 1024 microframes, ep desc says 2040 microframes [ 31.750352] hub 1-5:1.0: USB hub found [ 31.750751] hub 1-5:1.0: config failed, can't read hub descriptor (err -22)
% ls -l /dev/ttyUSB* zsh: no matches found: /dev/ttyUSB* % arecord -l **** List of CAPTURE Hardware Devices **** card 1: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: PCH [HDA Intel PCH], device 2: ALC892 Alt Analog [ALC892 Alt Analog] Subdevices: 1/1 Subdevice #0: subdevice #0
If I use a PCI USB I/F card, it works all right.
% lspci | grep -i usb 00:14.0 USB controller: Intel Corporation 9 Series Chipset Family USB xHCI Controller 00:1a.0 USB controller: Intel Corporation 9 Series Chipset Family USB EHCI Controller #2 00:1d.0 USB controller: Intel Corporation 9 Series Chipset Family USB EHCI Controller #1 04:02.0 USB controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 62) 04:02.1 USB controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 62) 04:02.2 USB controller: VIA Technologies, Inc. USB 2.0 (rev 65)
[ 20.941489] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 31.248006] usb 6-1: new full-speed USB device number 2 using uhci_hcd [ 31.397184] usb 6-1: New USB device found, idVendor=0451, idProduct=2046 [ 31.397187] usb 6-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 31.399220] hub 6-1:1.0: USB hub found [ 31.401185] hub 6-1:1.0: 4 ports detected [ 31.681442] usb 6-1.1: new full-speed USB device number 3 using uhci_hcd [ 31.961668] usb 6-1.1: New USB device found, idVendor=08bb, idProduct=2901 [ 31.961679] usb 6-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 31.961681] usb 6-1.1: Product: USB Audio CODEC [ 31.961682] usb 6-1.1: Manufacturer: Burr-Brown from TI [ 31.967731] input: Burr-Brown from TI USB Audio CODEC as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/0000:04:02.0/usb6/6-1/6-1.1/6-1.1:1.3/0003:08BB:2901.0004/input/input19 [ 32.020824] hid-generic 0003:08BB:2901.0004: input,hidraw3: USB HID v1.00 Device [Burr-Brown from TI USB Audio CODEC ] on usb-0000:04:02.0-1.1/input3 [ 32.093781] usb 6-1.2: new full-speed USB device number 4 using uhci_hcd [ 32.100961] usbcore: registered new interface driver snd-usb-audio [ 32.210894] usb 6-1.2: New USB device found, idVendor=10c4, idProduct=ea60 [ 32.210898] usb 6-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 32.210899] usb 6-1.2: Product: CP2102 USB to UART Bridge Controller [ 32.210900] usb 6-1.2: Manufacturer: Silicon Labs [ 32.210911] usb 6-1.2: SerialNumber: IC-7410 00000000 [ 33.254446] usbcore: registered new interface driver usbserial [ 33.254462] usbcore: registered new interface driver usbserial_generic [ 33.254534] usbserial: USB Serial support registered for generic [ 33.267204] usbcore: registered new interface driver cp210x [ 33.267218] usbserial: USB Serial support registered for cp210x [ 33.267244] cp210x 6-1.2:1.0: cp210x converter detected [ 33.267303] usb 6-1.2: cp210x converter now attached to ttyUSB0
% ls -l /dev/ttyUSB* crw-rw---- 1 root dialout 188, 0 May 3 20:37 /dev/ttyUSB0 % arecord -l **** List of CAPTURE Hardware Devices **** card 1: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: PCH [HDA Intel PCH], device 2: ALC892 Alt Analog [ALC892 Alt Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 2: CODEC [USB Audio CODEC], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0
Here is sprigmm on my new PC.
